Shout Box

...loading shoutbox...











« previous next »
Pages: [1]   Go Down

Author Topic: Going to do a headgasket on 02 660  (Read 2607 times)

Offline ein

  • Newbie
  • *
  • Posts: 29
  • Street Cred: 0
Going to do a headgasket on 02 660
« on: December 15, 2010, 05:25:43 PM »


Just got gasket kit in mail. Proablly going to try and do this project tomorrow! I have put many headgaskets on cars/trucks/heavy equipment  but never on a small engine. Any advice or is it about standard?? one problem i forsee is i only have 1/2 in torque wrench that only goes down to like 12 ft/lbs.... might have to find one that does in/lbs... haha  WISH ME LUCK!!  I have had this broken quad for like a year now ... lol
Logged

Offline ein

  • Newbie
  • *
  • Posts: 29
  • Street Cred: 0
Re: Going to do a headgasket on 02 660
« Reply #1 on: December 24, 2010, 11:24:16 AM »
Officially started on the project today!! Will post up pictures tonight!
Logged

Offline Colorado700R

  • Always the big spoon!
  • Admin Pimp
  • Hero Member
  • *****
  • Posts: 15250
  • Street Cred: 50
  • Carpe Cerevisi!!! (Sieze the beer!!)
    • Email
Re: Going to do a headgasket on 02 660
« Reply #2 on: December 24, 2010, 01:48:35 PM »
is all you are doing is the gaskets?  Depending on the amount of hours on the quad, you might think about reringing the piston.  My thoughts are that you're already right there to do it anyway.....just a thought.

Aaron
Logged

Offline ein

  • Newbie
  • *
  • Posts: 29
  • Street Cred: 0
Re: Going to do a headgasket on 02 660
« Reply #3 on: December 24, 2010, 03:53:07 PM »
It has a used stock piston/ jug I got off eBay that is in like new condition. Bought the quad as a basket case off craigslist. It's been a project for about 8 months now. Just finally getting around to finishing it!! Got the head on and torqued down but I had to stop so I could go eat dinner with the family... Lol looking forward to Monday so I can pick up where I left off. Will post up pics when I get around a computer.
Logged

Offline ein

  • Newbie
  • *
  • Posts: 29
  • Street Cred: 0
Re: Going to do a headgasket on 02 660
« Reply #4 on: December 24, 2010, 04:56:55 PM »


Logged

Offline ein

  • Newbie
  • *
  • Posts: 29
  • Street Cred: 0
Re: Going to do a headgasket on 02 660
« Reply #5 on: December 27, 2010, 11:45:04 AM »
Got it started!!! Still have quite a list of stuff to fix though... Carb float is stuck, adjust the valves, battery is weak, put on exhaust, figure out why it thinks it is in reverse, figure out why clutch plates are sticking, flush cooling system .... Haha
Logged

Offline Krandall

  • Führer
  • SiteAdmin
  • Hero Member
  • *****
  • Posts: 36323
  • Street Cred: 1337
  • Dracus II
    • Yamaha Raptor Forum
    • Email
Re: Going to do a headgasket on 02 660
« Reply #6 on: February 01, 2011, 02:21:09 PM »
thinks its in reverse meaning the light is on all the time?

when its in N. does the light come on properly?
Logged


Sponsored by:
Yamaha Raptor Forum

PCIII Maps Here:
http://www.krandall.com

Cowards die many times before their deaths The valiant never taste of death but once

Offline ein

  • Newbie
  • *
  • Posts: 29
  • Street Cred: 0
Re: Going to do a headgasket on 02 660
« Reply #7 on: February 12, 2011, 05:58:10 PM »
Yes the reverse light stays on all the time. Don't have the neutral or rev wire hooked up at all. Anyone have a wiring diagram for one of these? I couldn't fine one in the serv manual.
Logged

Offline Mad Dog

  • Grand Masta Sexy
  • VIP
  • Hero Member
  • *
  • Posts: 1690
  • Street Cred: 24
Re: Going to do a headgasket on 02 660
« Reply #8 on: February 12, 2011, 07:02:43 PM »
Last page of the service manual.
Logged
Pages: [1]   Go Up
« previous next »