Extended stock swinger PICS!

[Out Back Welding]

Finished putting it all back togeather.  Thing is freaking awesome!

Between the 15t front sprocket, the new spring/rebuild/revalve, and the +3 swinger....I dont know what to go on about first..Im impressed with all three new mods

[Shawnz]

Did the stock brake line work?    Do you think it'd work if you would have went +4?

Thanks,

Shawn

[Out Back Welding]

Did the stock brake line work?    Do you think it'd work if you would have went +4?

Thanks,

Shawn

                                                                 

 I checked to see if the stock lines would have worked, they won't, even on a +3.

[SprinterX]

Did the stock brake line work?    Do you think it'd work if you would have went +4?

Thanks,

Shawn

                                                                 

 I checked to see if the stock lines would have worked, they won't, even on a +3.

Take note when looking for an aftermarket brake line. You want one where the bango fittings are at 90* to each other.

[Out Back Welding]

Did the stock brake line work?    Do you think it'd work if you would have went +4?

Thanks,

Shawn

                                                                 

 I checked to see if the stock lines would have worked, they won't, even on a +3.

Take note when looking for an aftermarket brake line. You want one where the bango fittings are at 90* to each other.

I'll have to double check who i got mine from but u buy the bango's seperately, and you just screw them on at any angle u want

[SprinterX]

Did the stock brake line work?    Do you think it'd work if you would have went +4?

Thanks,

Shawn

                                                                 

 I checked to see if the stock lines would have worked, they won't, even on a +3.

Take note when looking for an aftermarket brake line. You want one where the bango fittings are at 90* to each other.

I'll have to double check who i got mine from but u buy the bango's seperately, and you just screw them on at any angle u want

That's great, mine were swagged the same and I had to twist them slightly to fit. Good thing I bought one that was a little extra lengthy.

[Out Back Welding]

Did the stock brake line work?    Do you think it'd work if you would have went +4?

Thanks,

Shawn

                                                                 

 I checked to see if the stock lines would have worked, they won't, even on a +3.

Take note when looking for an aftermarket brake line. You want one where the bango fittings are at 90* to each other.

I'll have to double check who i got mine from but u buy the bango's seperately, and you just screw them on at any angle u want

That's great, mine were swagged the same and I had to twist them slightly to fit. Good thing I bought one that was a little extra lengthy.

Yeah mines a little lengthy aswell.

[Krandall]

Did the stock brake line work?    Do you think it'd work if you would have went +4?

Thanks,

Shawn

                                                                 

 I checked to see if the stock lines would have worked, they won't, even on a +3.

Doesn't work on a +2 either.

[Out Back Welding]

I did find out today that with the +3 you can still stand it straight up on the rear grab bar and tires no problem.

[Out Back Welding]

Few little more updated pics. Everything holds up great!

People say: "You welded that? You can't even tell..."

[Krandall]

That really turned out great!!!!

[Firemann32]

So when do you wanna do my 660's?

[Out Back Welding]

Still Holding up great not even one hair line crack! Meanwhile I've created like 30+ of these, and no problems eather I Got a few different pics on Facebook in the photo section. http://www.facebook.com/pages/Out-Back-Aluminum-Welding/311318575581856

[zx10r203]

Whats the pricing on these??

[Out Back Welding]

Whats the pricing on these??

Varies, Most are $300.00 shipped